QJ（D/S）DX型气动橡胶调节蝶阀
产品简介
详细信息
一、概述Outline
QJ（D/S）DX型精小型气动橡胶蝶阀是由气动活塞式执行机构和衬里蝶阀组成，属旋转类控制阀。
该产品以压缩空气为动力源，接受控制仪表的4-20mA信号（或开关信号），通过电-气阀门定位器（或电磁阀）实现对阀门的连续调节（或位式控制）。
橡胶衬里蝶阀是一种阀体内腔衬有橡胶的防腐蚀蝶阀。控制腐蚀性流体不与阀体接触，阀体可用普通铸铁或碳钢，由此降低蝶阀的成本。衬里材料有各种橡胶可供选择，还可更换。
该产品结构简单，输出力矩大，性能*。蝶阀通常适用于控制密封要求比较高的腐蚀性流体。
QJ （D / S） DX-type fine small pneumatic rubber valve is pneumatic piston actuator and lining butterfly valve, is a rotary type control valve.
The product is compressed air as power source, to accept 4-20mA control signal meter （or switch signals）, through the electric - gas valve locator （or solenoid valve） to achieve the continuous adjustment of the valve （or bit control）.
Rubber lined butterfly valve is a body cavity lined with rubber anti-corrosion butterfly. Corrosion control and body fluid does not contact the valve body can be an ordinary cast iron or steel, thus reducing the cost of butterfly. There are a variety of rubber lining materials available, can be replaced.
The product is simple, the output torque, and superior performance. Control valve normally sealing requirements for high corrosive fluids.
二、主要技术参数Main technical parameters
| 公称通径mm | 50 | 65 | 80 | 100 | 125 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 600 | |
| 额定流量系数Kv | 71 | 100 | 198 | 340 | 500 | 770 | 1360 | 2130 | 3060 | 4160 | 5450 | 6900 | 8500 | 12000 | |
| 公称压力Mpa | 0.6、1.0、1.6 | ||||||||||||||
| 连接方式 Connection | 对夹式（管道法兰标准：JB/T79-94、GB9113-2000 Wafer （pipe flange standard: JB/T79-94, GB9113-2000） | ||||||||||||||
| 介质温度℃ Temperature | -20~+180 | ||||||||||||||
| 输入信号Input signal | 0.4~0.6Mpa/调节型0.02-0.1Mpa（4-20mA） 0.4 ~ 0.6Mpa / Regulated 0.02-0.1Mpa （4-20mA） | ||||||||||||||
| 额定行程Rated travel | 调节型：70° 切断型：90° Modulating: 70 ° cut-off: 90 ° | ||||||||||||||
| 环境温度℃ Temperature | -40~+150、-40~+180 | ||||||||||||||
| 气源接口 Air Connection | 1/8 ″G 、 NAMUR1/4″G | ||||||||||||||
| 固有流量特性 Inherent flow characteristic | 近似等百分比Approximay equal percentage | ||||||||||||||
|
| |||||||||||||||
| 泄露等级 Leakage level | ANSIB16.104 IV级、VI（软密封） ANSIB16.104 IV level, VI （soft seal） | ||||||||||||||
注：允许压差可参照QJD（S）DR型气动蝶阀该指标
Note: Allow pressure to refer QJD （S） DR pneumatic valve of the indicators
三、性能指标Performance indicators
| 项目Item | 带定位器指标值Index value with locator | ||
| 基本误差Basic error% | ±2.5 | ||
| 回差Hysteresis% | 2.5 | ||
| 死区Dead% | 1.0 | ||
| 始终点偏差 Always point deviation% | 气开 Open air | 始点 Starting point 终点End | ±2.5 |
| ±2.5 | |||
| 气关 Gas off | 始点 Starting point 终点End | ±2.5 | |
| ±2.5 | |||
四、执行机构转扭及动作时间Twist and turn actuators operating time
| 执行机构型号AGT | 63×90 | 75×90 | 83×90 | 92×90 | 110×90 | 118×90 | 127×90 | 160×90 | 210×90 | 254×90 | 255×90 | |
| 扭矩N.m | 400Kpa | 23.2 | 40.0 | 56.0 | 77.6 | 112.8 | 168.0 | 220.0 | 440.0 | 948.0 | 1740.0 | 2172.0 |
| 500Kpa | 29.0 | 50.0 | 70.0 | 97.0 | 141.0 | 210.0 | 275.0 | 550.0 | 1185.0 | 2715.5 | 2715.0 | |
| 动作时间（S） | 0.241 | 0.333 | 0.429 | 0.444 | 0.461 | 0.60 | 0.857 | 1.62 | 3.33 | 6.00 | 7.50 | |
注：1、双作用执行机构在75%负载情况下的动作时间 2、缩短动作时间可允许非标配置
Note: 1, double-acting actuators at 75% load case, the action time of 2 to shorten the operating time to allow non-standard configuration
五、可配附件Available Accessories
调节型：电-气阀门定位器，空气过滤减压器，手轮机构等。
切断型：定位开关，空气过滤减压器，电磁阀，手轮机构等。
Adjustment type: electric - gas valve positioner, air filter regulator, hand wheel institutions.
Cut-off: position switch, air filter regulator, solenoid valve, hand wheel institutions.
六、主要零件材质与内腔衬材料Material of main parts and cavity lining material
| 零件名称Part Name | 材料Material |
| 阀体Body | 各种橡胶、聚四氟 A variety of rubber, PTFE |
| 蝶板Disc | 灰铸铁、球墨铸钢、铸钢、不锈钢及特殊材料 Gray cast iron, ductile cast steel, cast steel, stainless steel and special materials |
| 密封圈Ring | 球墨铸钢、铸钢、合金钢、不锈钢 Ductile cast steel, cast steel, alloy steel, stainless steel |
| 阀杆Stem | 2Cr13、不锈钢 2Cr13, Stainless Steel |
| 填料Filler | O型圈、柔性石墨 O-ring, flexible graphite |
1.阀体内腔衬材料Body cavity lining materials
| 材料品种 Variety of materials | 氯丁橡胶 Neoprene | 丁腈橡胶NBR | 乙丙橡胶EPDM | 硅橡胶Silicone rubber | 氟橡胶Viton |
| 代号Code | X或J | X 或JA | XB或 JB | XD或 JD | XE 或JE |
| 耐zui高温度 Maximum temperature resistance | 82℃ | 93℃ | 150℃ | 250℃ | 204℃ |
| 耐zui低温度 Minimum temperature resistance | -40℃ | -40℃ | -40℃ | -70℃ | -23℃ |
| 适用工作温度 Suitable temperature | ≤65℃ | ≤80℃ | ≤120℃ | ≤200℃ | ≤180℃ |
七、外形尺寸Dimensions
| 标准值Standard value | 参考值Reference | ||||||||
| DN | L | D | D1 | Z-d | H | H0 | A | B | W（kg） |
| 50 | 43 | 99 | 125 | 4-18 | 170 | 130 | 45 | 120 | 24.7 |
| 65 | 46 | 118 | 145 | 4-18 | 170 | 145 | 45 | 120 | 25.6 |
| 80 | 46 | 132 | 160 | 4-18/8-18 | 320 | 186 | 160 | 240 | 27 |
| 100 | 52 | 156 | 180 | 8-18 | 320 | 192 | 310 | 100 | 30.8 |
| 125 | 56 | 184 | 210 | 8-18 | 345 | 200 | 370 | 118 | 37.6 |
| 150 | 56 | 211 | 240 | 8-22 | 385 | 230 | 370 | 118 | 43.2 |
| 200 | 60 | 266 | 295 | 8-22/12-22 | 471 | 297 | 450 | 143 | 100.8 |
| 250 | 68 | 319 | 350 | 12-22 | 533 | 327 | 450 | 143 | 118.5 |
| 300 | 78 | 370 | 400 | 12-22 | 606 | 364 | 535 | 178 | 159 |
| 350 | 78 | 429 | 460 | 16-22 | 694 | 404 | 535 | 178 | 180.7 |
| 400 | 102 | 480 | 515 | 16-26 | 757 | 444 | 630 | 248 | 216.8 |
| 450 | 114 | 530 | 565 | 20-26 | 814 | 472 | 1162 | 232 | 266.1 |
| 500 | 127 | 582 | 620 | 20-26 | 902 | 522 | 1162 | 232 | 325 |
| 600 | 154 | 682 | 725 | 20-30 | 1048 | 590 | 1380 | 318 | 355 |
| 700 | 165 | 794 | 840 | 24-30 | 1277 | 810 | 1380 | 318 | 585 |
| 800 | 190 | 901 | 950 | 24-33 | 1385 | 844 | 1860 | 350 | 798 |
| 900 | 203 | 1001 | 1050 | 28-33 | 1490 | 890 | 1860 | 350 | 906 |
| 1000 | 216 | 1112 | 1160 | 28-36 | 1620 | 950 | 1860 | 350 | 1055 |